NF G07-013-11-1988 纺织.印染牢度试验.第E11部分:水洗牢度
作者:标准资料网 时间:2024-05-12 14:05:11 浏览:9446
来源:标准资料网
【英文标准名称】:TEXTILES.TESTSFORCOLOURFASTNESS.PARTE11:COLOURFASTNESSTOSTEAMING.
【原文标准名称】:纺织.印染牢度试验.第E11部分:水洗牢度
【标准号】:NFG07-013-11-1988
【标准状态】:作废
【国别】:法国
【发布日期】:1988-08
【实施或试行日期】:1988-07-20
【发布单位】:法国标准化协会(AFNOR)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:染色;染色试验;水蒸气试验;色牢度;染料;印刷;大气压;纺织材料
【英文主题词】:dyeing;dyeingtests;colourtests;dyes;colourfastness;colourfastness;atmosphericpressure;printing;textiles;watervaportests;water-vapourtests
【摘要】:
【中国标准分类号】:W70
【国际标准分类号】:
【页数】:2P;A4
【正文语种】:其他
【英文标准名称】:TestingofBituminousMaterialsforRoadBuildingandRelatedPurposes;DeterminationofSofteningPointinaccordancewithWilhelmi
【原文标准名称】:筑路和相关用途沥青材料的检验.第15部分:根据威廉米法测定软化点
【标准号】:DIN1996-15-1975
【标准状态】:现行
【国别】:德国
【发布日期】:1975-12
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:定义;软化点;沥青材料;胶泥;道路建筑;质量(物质)
【英文主题词】:softeningpoint;mastics;bituminousmaterials;mass;definitions;roadconstruction
【摘要】:Testingofbituminousmaterialsforroadbuildingandrelatedpurposes;determinationofthesofteningpointWilhelmiEssaisdesproduitsbitumineuxpourlesrevêtementsroutiersetautresapplicationss'yrapportant;déterminationdupointderamollissem
【中国标准分类号】:E43
【国际标准分类号】:75_140
【页数】:2P;A4
【正文语种】:德语
Product Code:SAE J810
Title:Classification of Common Surface Imperfections in Sheet Steel
Issuing Committee:Sheet And Strip Steel Committee
Scope: Common or obvious surface imperfections, which sometimes occur in sheet steel, are normally visible to the naked eye before or after fabrication. Illustrations and definitions of these imperfections are contained in this SAE Information Report. The identifying names are those commonly used throughout the steel industry. The imperfections identified include the major and most often encourntered imperfections known to exist at this time. These imperfections are variable in appearance and severity. Extreme conditions have been selected in some instances in order to obtain suitable photographs.
Rationale: Common or obvious surface imperfections, which sometimes occur in sheet steel, are normally visible to the naked eye before or after fabrication. Illustrations and definitions of these imperfections are contained in this SAE Information Report. The identifying names are those commonly used throughout the steel industry. The imperfections identified include the major and most often encourntered imperfections known to exist at this time. These imperfections are variable in appearance and severity. Extreme conditions have been selected in some instances in order to obtain suitable photographs.
